|
|
|
|
| Interface Modules
|
|
|
| |
| Motion Controller Lineup |
 |
|
| Recommended |
 | PCI-7208
Isolated 4-Axis Pulse Motion Controller PCI Product (Linear Interpolation and Encoder Input +5 Vdc)
The PCI-7208 is a motion controller board for PCI-based computers. It supports 4 axes and requires pulse-train input type motor amplifier according to the motor type. The pulse output circuit provides a high-speed photo-isolated open-collector output, and the pulse output rate is up to 1 MHz. The limit signal input circuit is photo-isolated. This board incorporates a pulse controller X3203A per axis, supporting linear interpolation. You can also change the velocity even if the axis is moving.
|  | PCI-7209
Isolated 2-Axis Pulse Motion Controller PCI Product (Linear Interpolation and Encoder Input +5 Vdc)
The PCI-7209 is a motion controller board for PCI-based computers. It supports 2 axes and requires pulse-train input type motor amplifier according to the motor type. The pulse output circuit provides a high-speed photo-isolated open-collector output, and the pulse output rate is up to 1 MHz. The limit signal input circuit is photo-isolated. This board incorporates a pulse controller X3203A per axis, supporting linear interpolation. You can also change the velocity even if the axis is moving.
|  | PCI-7211CA
Isolated 2-Axis Pulse Motion Controller PCI Product (Linear Interpolation and Encoder Input +5 Vdc)
|  | PCI-7212C
Isolated 8-Axis Pulse Motion Controller PCI Product (Circular and Linear Interpolation)
The PCI-7212C is a motion controller board for PCI-based computers. It supports 8 axes of a stepper motor and requires an appropriate pulse-train input type motor amplifier according to the motor type. This board supports smooth S-curve motion profile and linear interpolation. You can also change the velocity and target position even if the axis is moving.
|  | PCI-7301
Isolated 4-Axis DC Motor Driver PCI Product (H Bridge Output)
The PCI-7301 is a DC motor driver board for PCI-based computers. It directly drives four bi-directional DC motors and four solenoids. This board incorporates the overcurrent and overvoltage protection circuits and supports 500 mA of current drive per channel.
|  | PCI-7404M
4-Axis Pulse Motion Controller PCI Product (Circular, Linear Interpolation, and Encoder Input +24 Vdc)
The PCI-7404M, a motion controller product for PCI-based computers, supports four axes of a stepper or servo motor. This product controls four axes individually and supports linear interpolation operation among four axes by configuring parameters. With synchronous cables, up to eight interface modules
(32 axes) can operate synchronously and the following three parallel operations are allowed; clock synchronization, simultaneous start, and simultaneous stop. This product also supports circular interpolation between two axes. This product incorporates PCL6045 (Nippon Pulse Motor Co., Ltd.) or equivalent as a controller LSI, which supports smooth S-curve motion profile.
|  | PCI-7404V
4-Axis Pulse Motion Controller PCI Product (Circular, Linear Interpolation, and Encoder Input +5 Vdc)
The PCI-7404V, a motion controller product for PCI-based computers, supports four axes of a stepper or servo motor. This product controls four axes individually and supports linear interpolation operation by configuring parameters among four axes. With synchronous cables, up to eight interface modules
(32 axes) can operate synchronously and following three parallel operations are allowed; clock synchronization, simultaneous start, and simultaneous stop. This product also supports circular interpolation between two axes. This product incorporates PCL6045 (Nippon Pulse Motor Co., Ltd.) or equivalent as a controller LSI, which supports smooth S-curve motion profile.
|  | PCI-7414M
Isolated 4-Axis Pulse Motion Controller PCI Product (Circular, Linear Interpolation, and Encoder Input +24 Vdc)
The PCI-7414M, a motion controller product for PCI-based computers, supports four axes of a stepper or servo motor. This product controls four axes individually and supports linear interpolation operation among four axes by configuring parameters. With synchronous cables, up to eight interface modules
(32 axes) can operate synchronously and the following three parallel operations are allowed; clock synchronization, simultaneous start, and simultaneous stop. This product also supports circular interpolation between two axes. This product incorporates PCL6045 (Nippon Pulse Motor Co., Ltd.) or equivalent as a controller LSI, which supports smooth S-curve motion profile.
|  | PCI-7414V
Isolated 4-Axis Pulse Motion Controller PCI Product (Circular, Linear Interpolation, and Encoder Input +5 Vdc)
The PCI-7414V, a motion controller product for PCI-based computers, supports four axes of a stepper or servo motor. This product controls four axes individually and supports linear interpolation operation by configuring parameters among four axes. With synchronous cables, up to eight interface modules
(32 axes) can operate synchronously and following three parallel operations are allowed; clock synchronization, simultaneous start, and simultaneous stop. This product also supports circular interpolation between two axes. This product incorporates PCL6045 (Nippon Pulse Motor Co., Ltd.) or equivalent as a controller LSI, which supports smooth S-curve motion profile.
|
If you have any questions, feel free to contact us. | |
|
|
|
|
Sign up for product updates
